Big block chevy valve adjustment chart

A. Starting with #1 cylinder, turn the engine over until the exhaust pushrod just begins to move up. B. At this point, stop and adjust the intake valve on the same cylinder. 1) Tighten the rocker until you can roll the pushrod between your thumb and forefinger with the slightest bit of resistance. 2) At this point tighten between an additional ...

May 16, 2020 ... Today we are showing you exactly how to install lifters, pushrods, rocker arms and an intake manifold for a Gen IV Chevrolet Big Block V8!Apr 4, 2010 · The simplest, most accurate way to adjust the valves on any Chevy V8 is with the engine off. It's also the best way to keep hot oil from spewing all over your engine compartment. Do a search of the EO/IC method of adjusting valves. Place a few 1/4” thick strips of modeling clay across the upper half of the piston. Put a light coat of oil on top of the modeling clay and the valves in the cylinder head to keep the clay and valve from sticking. Place the head gasket you will be using on the block and bolt the head on with five or six head bolts.simple instructions for setting valve lash solid lifters sbc no cam specs. When the exhaust valve starts to open, you adjust the intake valve on that cylinder. After intake valve opens completely and is closing, adjust the exhaust valve on that cylinder. To adjust valves insert the feeler gauge between the rocker and valve and tighten until ... Valve sizes are 2.250/1.880 inches. The current “bad-boy” Bowtie race head is PN 12363425 (casting number 14044861), a bare head with 380-cc intakes and valve seats for 2.19/1.88-inch valves. Exhaust port exits are raised 3/4 inch and feature a distinctive vane, giving rise to the popular nickname of the “W” port head. circle on ANY OEM Chevrolet cam for adjustment, and the factory-recommended clearance on other OEM Chevrolet small-block solid-lifter cams should be factored as well by the 1.37:1-vs.-1.5:1 ratio difference at the lash point and rounded-down to the next-nearest thousandth or two to ensure that the valves are picked up and seated at ramp velocity.

simple instructions for setting valve lash solid lifters sbc no cam specs. When the exhaust valve starts to open, you adjust the intake valve on that cylinder. After intake valve opens completely and is closing, adjust the exhaust valve on that cylinder. To adjust valves insert the feeler gauge between the rocker and valve and tighten until ...Unfortunately, I don't have cam specs, as I bought my car turnkey and the seller didn't have the cam card. I'm just curious what a "typical" range should be for valve lash on a big block Chevy. (Iron block, aluminum heads). I checked, and the lash was .036 COLD, which according to my math is about .042 hot. That seems loose no matter what …Provided those marks are correct the intake and exhaust valves will be closed. When 1 is on TDC 6 is rocking. The second approach is to adjust adjacent valve when the other valve is rocking (at highest possible position so you avoid overlap of valves). In this case when the exhaust valve is wide open, one knows for sure the intake …The first step to decoding the Chevy engine block code is to locate and identify the code on the engine assembly stamp correctly. Next understand the block code. The code has 15 ch...Valves. The original Chevy 265-ci small-block began life actuating diminutive 1.72- and 1.50-inch intake and exhaust valves. In the evolution of the small-block, now displacing as much as 454 inches out of a standard deck height block, these big-bore small-blocks can now accommodate up to impressive 2.150- and 1.625-inch valve sizes.Jun 4, 2009 · 1. Remove the valve covers, and pick a cylinder that you are going to set the preload on. 2. Hand rotate the engine in its normal direction of rotation and watch the exhaust valve on that particular cylinder. When the exhaust valve begins to open, stop and adjust that cylinder's intake rocker arm. (Why? With lash or preload set on the intake, we can now slowly turn the engine again clockwise until the intake valve is halfway down the closing side. Once the intake valve reaches this point, this places the exhaust lobe on Cylinder One on the base circle. Now we can set lash/preload on the exhaust.“Lash is required to deal with the change in adjustment from hot to cold as the metal expansion rates differ between the block, heads, pushrod, valves and other components,” explains Billy Godbold of Comp …

ENGINE OFF Valve Adjustment Procedure - The Quick and Accurate Way: First, view this simple chart below for Small and Big Block Chevy Engines. Do you …As the metal in the valve train expands the lifter, pushrod, and valve stem elongate - taking up clearance in the system. If setting cold, add a 'couple-thou' (@.002") to the "HOT" setting and recheck once the engine has reached operating temps. IIRC, the lash settings given are correct - or close enough. Some of the higher HP BB's recommended ...The ARP Perma-Lock rocker arm adjusters feature a 12-point head with a small shoulder stop at the bottom that prevents the wrench from slipping off the hex. This allows you to place a standard box-end wrench over the adjuster that will remain in place. This is really nice when setting lash as it’s far less clumsy. (Image/Jeff Smith)Start with cylinder number one (1). When the exhaust valve begins to move, adjust the intake valve to zero lash plus an additional ½ turn more. Rotate the engine over again until the intake valve reaches maximum lift and is almost all the way back down. Then set the exhaust valve to zero lash plus ½ turn. Adjust the valves on each cylinder in ...

Culver's flavor of the day dodgeville.

Start with cylinder number one (1). When the exhaust valve begins to move, adjust the intake valve to zero lash plus an additional ½ turn more. Rotate the engine over again until the intake valve reaches maximum lift and is almost all the way back down. Then set the exhaust valve to zero lash plus ½ turn. Adjust the valves on each cylinder in ...Most hydraulic lift camshafts will require zero lash for the proper adjustment. The process will be the same whether you have stamped steel rockers or roller tip rockers. To achieve zero lash, tighten down the rocker as you spin the pushrod in your fingers, do this until you notice slight resistance as you spin the pushrod (this is zero lash).Step by step valve adjustmentNow rotate through the firing order (as he states every 90*) and set the next cylinder the same way. Two full revolutions and you should be back at #1 again and your lash should be where you put it in the first rotation. If running solids, break in the cam, then set the lash again hot by the cam card.#2 · Jul 19, 2006. The Chilton's method works fine. You set the crank at #1 firing position and adjust 8 varous valves. Then turn the crank 360 degrees to #6 fire and do the other 8. It …

Apr 27, 2020 ... Small Block Chevy valve adjustment made easy. Myvintageiron7512•603K views · 8:17. Go to channel · Checking Hydraulic Lifter Preload on ...Valve sizes are 2.250/1.880 inches. The current “bad-boy” Bowtie race head is PN 12363425 (casting number 14044861), a bare head with 380-cc intakes and valve seats for 2.19/1.88-inch valves. Exhaust port exits are raised 3/4 inch and feature a distinctive vane, giving rise to the popular nickname of the “W” port head.Apr 4, 2010 · The simplest, most accurate way to adjust the valves on any Chevy V8 is with the engine off. It's also the best way to keep hot oil from spewing all over your engine compartment. Do a search of the EO/IC method of adjusting valves. Valves. The original Chevy 265-ci small-block began life actuating diminutive 1.72- and 1.50-inch intake and exhaust valves. In the evolution of the small-block, now displacing as much as 454 inches out of a standard deck height block, these big-bore small-blocks can now accommodate up to impressive 2.150- and 1.625-inch valve sizes.46 posts · Joined 2010. #1 · Jun 25, 2012. I was wondering if when setting the valve lash on solid lifters if you can set them by getting on TDC on #1 adjusting the exhaust on 1,3,4,8 and the Intake on 1,2,5,7. Then rotating the motor 360 degrees to #6 TDC and adjusting the exhaust on 2,5,6,7 and the Intake on 3,4,6,8 or does it need to be ...Here is the order to adjust your valves on a Ford 260, 289 and 302 ... 289 and 302 Valve Adjusting Order Need to adjust your valves on a Ford Small Block? This is the chart that will help you do it. This is for engines with the older firing order. If you car has a later model cam shaft you should use the 302 HO / 351W order which is different ... guide plate, but leave them loose. Screw adjustment nuts about ½ inch down on studs. Spread girdle apart as far as possible. Place girdle over adjuster nuts approximately 2-7/8” (308, 320, 340, 360, and 370 heads) or 2-5/8” (Pro1 and Iron Eagle heads) from the top of the girdle to the bare valve cover surface. Squeeze girdle closed by hand ... Continue to rotate the engine by hand. Now the intake lifter will rise, go to max lift and start closing. Stop there and adjust the lash for the exhaust valve. Repeat for the other 7 cylinders. On any cam, when the exhaust valve just starts to open, the intake lifter will be on it base circle and ready to be lashed.After adjusting valves on your small-block Chevy, run the engine. It breaks the cam – and then readjusts while the engine is still running. After the break-in, when the engine is idling, loosen the rocker till you hear a click. Now slowly tighten it until the click stops. Then turn ¼, and tighten another ½ turn.Valve adjustment sequence for chevy 502 big blockA guide to vortec vs oe small block chevy heads Lash valve engine adjust lifters set solid setting adjustment chevy 350 lifter pro enginelabs performance adjusting throwback thursday tappet flatSmall block chevy valve adjustment made easy.Provided those marks are correct the intake and exhaust valves will be closed. When 1 is on TDC 6 is rocking. The second approach is to adjust adjacent valve when the other valve is rocking (at highest possible position so you avoid overlap of valves). In this case when the exhaust valve is wide open, one knows for sure the intake …Do you know where your gas shut-off valve is located? Read on to learn where to find it, how to turn it off, and how to shut gas off to specific appliances Expert Advice On Improvi...

EZ Read simple diagram of the typical valve layout of a Big Block Chevy Cylinder Head. ... Drill and Tap Chart - BRITISH; Valve Adjustment; Ford 302 HO and 351W; Ford ...

Step by step valve adjustmentAdjusting the intake valve on “opposite in firing order” cylinder (see the above chart) is now possible. Remember, the opposite is engine firing order dependent. This article uses the small and big block Chevy engines as …Tighten until the clacking stops and tighten 1/8th turn. For general use 1/4 to 1/2 turn is good as long as your consistent with every tappet. The less of a turn the faster your going to hear and recognize …Jul 2, 2006 · Continue to rotate the engine by hand. Now the intake lifter will rise, go to max lift and start closing. Stop there and adjust the lash for the exhaust valve. Repeat for the other 7 cylinders. On any cam, when the exhaust valve just starts to open, the intake lifter will be on it base circle and ready to be lashed. 3. Finalizing the Valve Adjustment Process. The final step valve adjustment procedure on a 350 Chevy is crucial yet often overlooked. Once all adjustments are made, it’s essential to re-install the valve covers securely. This not only protects the internal components but also signifies the completion of your task.This instructional video describes two different methods of adjusting valves on engines with solid lift camshafts. The video also briefly talks about firing ...Is there a way to select and tap flogging coldly on hydraulic lifters on SBC? A friend claims with the spring locked, to lock down the nut until the rocker arm doesn't move when back off a half a turn and your done.Continue to rotate the engine by hand. Now the intake lifter will rise, go to max lift and start closing. Stop there and adjust the lash for the exhaust valve. Repeat for the other 7 cylinders. On any cam, when the exhaust valve just starts to open, the intake lifter will be on it base circle and ready to be lashed.

Deposit cash usaa atm near me.

Libertyville to union station.

You need to adjust the valves. Here is the method I use and suggest for small block Chevy engines. I have posted this before and feel it will help you. Please read the part about the correct "feel" to get '0' lash. Adjusting Hydraulic Lifters On Small Block Chevrolet This method is with the engine OFF and spark plugs removed for easier rotation.1. Set Idle Correctly. This might seem way too simple, but for a carbureted street engine this is the most important tuning step you can make because street engines spend a majority of their time ...Conversely, spin the engine over until the intake valve opens and then starts to close, and the exhaust valve is sure to be closed at that point. Smith explains that since you always want to adjust a valve that is fully closed with the lifter on the base circle of the camshaft, an easy way to remember that is “EOIC” or exhaust open, intake ...After 40 mins to an hour of run time. Shut down; drain oil, change filter, install inner valve springs, hook up dizzy vacuum pod and PCV. Restart engine and do you final timing and carb work and adjust the HFT lifters at 1/4 turn with Engine Idling, then hook up the rest of your Vacuum Sources. Recommended Oil: Chevron Delo 400 …This instructional video describes two different methods of adjusting valves on engines with solid lift camshafts. The video also briefly talks about firing ...To use this method, to set an intake valve, rotate the engine until the exhaust valve is just opening on the cylinder you want to set the intake on. Set that intake. To set an exhaust valve, rotate the engine until the intake valve on that cylinder is almost to close. Set that exhaust valve. You can set the valves in any order you like, as long ...Chevy L36 Big Block 427. Available from 1966-1969 for Corvette applications only. The Chevy L36 427 is the little brother of the 1966-1969 big-block lineup. Compared to the other 7.0L V8s to follow, the L36 is the least powerful. The L36 was the first of the Mark IV 427s to hit the streets in 1966.Tighten the poly-lock of the rocker arm until the proper lash is found. When you get to your preferred lash, hold the adjuster nut in place and set it with the inner screw using an Allen wrench. The poly-lock adjuster nut adjusts the amount of valve lash while the set screw locks it into place. Finally, tighten with an adjustable torque wrench ...The Holley 650 (P/N: 0-4777-9) carb is factory jetted on the primary side with 67 main jets and a power valve with a 0.038-inch PVCR. The secondary side of this carb does not use a power valve to balance the fuel flow between the primary and secondary, so it uses 6-step larger 73 jets.After adjusting valves on your small-block Chevy, run the engine. It breaks the cam – and then readjusts while the engine is still running. After the break-in, when the engine is idling, loosen the rocker till you hear a click. Now slowly tighten it until the click stops. Then turn ¼, and tighten another ½ turn.Tighten until the clacking stops and tighten 1/8th turn. For general use 1/4 to 1/2 turn is good as long as your consistent with every tappet. The less of a turn the faster your going to hear and recognize … ….

First, view this simple chart below for Small and Big BlockChevy Engines and see if you can understand it. There is more of an explanationbelow the chart. For …Find CHEVROLET 7.4L/454 Chevy big block Mark IV Valves and get Free Shipping on Orders Over $109 at Summit Racing! Free Mount & Balance for Many Wheel & Tire Packages - Contact us for Details! ... Replacement, Intake, Stainless, 2.300 in. Diameter, 5.500 in. Length, Chevy, Big Block, AFR, Each. Part Number: AFR-7626-1. Not Yet …The great American sports car is going electric. GM shared the news this morning, and released the first images of the upcoming electric Chevrolet Corvette. The great American spor...May 21, 2022 ... In this video, Ryan shows you how to install push rods and rocker arms and how to set valve lash on a Chevy 350. He rebuilt this small block ...Feb 12, 2011. #1. If you intend to use any other cam than the stock hydraulic cam that came in a MARK V or MARK VI (gen 5 or gen 6 BIG BLOCK CHEVY) you'll most likely want to install one with more lift or duration to increase performance, that means you'll most likely need to upgrade the valve train to an adjustable valve train,IN most cases ...Here's the easiest way: 1. Get #1 piston to compression TDC, Cam gear at 12 o'clock crank gear at 12 o'clock. 2. Adjust the intake valves on cylinders 1, 2, 5, & 7 by loosening the rocker nut until play is in the pushrod then just take the up and down play in the pushrod and tighten the rocker nut an additional 1/2 turn.Place a few 1/4” thick strips of modeling clay across the upper half of the piston. Put a light coat of oil on top of the modeling clay and the valves in the cylinder head to keep the clay and valve from sticking. Place the head gasket you will be using on the block and bolt the head on with five or six head bolts.Tighten the poly-lock of the rocker arm until the proper lash is found. When you get to your preferred lash, hold the adjuster nut in place and set it with the inner screw using an Allen wrench. The poly-lock adjuster nut adjusts the amount of valve lash while the set screw locks it into place. Finally, tighten with an adjustable torque wrench ...Adjust #4 Intake Valve. with #2 cylinder Intake Valve at full valve lift .... Adjust #3 Intake Valve. Exhaust Valve Adjustment: ENGINE OFF! You will notice that this is the same procedure and sequence as the intake valves listed above. Only now you are adjusting ONLY the exhaust valves the same way. Big block chevy valve adjustment chart, Use adjustable pushrod to achieve proper pushrod length with valve lash. If your adjustment requires less than 1 full turn or more than 2 turns you will need a different pushrod length to achieve the correct adjustment. ... Now torque 1/4 bolts used on big block to 5-10 ft. lbs. When the stands are in place and tightened down, place the rocker ..., Apr 18, 2008 · what is the correct way to set the valve lash on a 454 big block chevy with a solid roller cam. Run the engine until it has reached normal operating temperature. Set the engine to the No. 1 firing position. Adjust the clearance between the valve stems and the rocker arms with a feeler gauge. , guide plate, but leave them loose. Screw adjustment nuts about ½ inch down on studs. Spread girdle apart as far as possible. Place girdle over adjuster nuts approximately 2-7/8” (308, 320, 340, 360, and 370 heads) or 2-5/8” (Pro1 and Iron Eagle heads) from the top of the girdle to the bare valve cover surface. Squeeze girdle closed by hand ... , The small and big block Chevy engines use a firing order of 1-8-4-3-6-5-7-2. What you do is separate the order into the two sides of the firing order. These are "exact" opposites that put the opposing valve at the correct location for adjustment, meaning the back side (base circle, or heal) of the cam lobe (see image at left)., With a 2.130-inch intake valve on this big-block, divide this diameter in half to establish the radius, which would be 1.065 inch. Apply a small amount of machinist dye to the valve pocket and ..., Oct 7, 2018 · There are 720 degrees in a full cycle to fire all 8 cylinders, so turning the crank 90 degrees at a time will allow us to adjust the valves on all 8 cylinders with just 2 full turns of the crank. If you knew that a small block Chevy's firing order is 1-8-4-3-6-5-7-2, then you would know that it is #8's turn to fire. , Nov 14, 2010 · This is different from flat-faced lifters which perform best at zero 0 to ½ turn of preload. Tests at Crane R&D have consistently shown best performance (for hydraulic roller cam valve trains) occurs with the preload set at 1 ¼ - 1 ½ turns down from zero lash. This adjustment will maximize power throughout the RPM range and increase the ... , Nov 22, 2013 · simple instructions for setting valve lash solid lifters sbc no cam specs. When the exhaust valve starts to open, you adjust the intake valve on that cylinder. After intake valve opens completely and is closing, adjust the exhaust valve on that cylinder. To adjust valves insert the feeler gauge between the rocker and valve and tighten until ... , 4102 posts · Joined 2011. #1 · Dec 1, 2015. Here's a pic of a static valve adjustment sequence I constructed for a buddy. Good for firing order 1-8-4-3-6-5-7-2 (chevy of course) However, I oriented the numerals on the pictorial banks to help indicate the relative position of each valve on a BBC. Print it out and use it if ya like it., Dec 1, 2015 · 4102 posts · Joined 2011. #1 · Dec 1, 2015. Here's a pic of a static valve adjustment sequence I constructed for a buddy. Good for firing order 1-8-4-3-6-5-7-2 (chevy of course) However, I oriented the numerals on the pictorial banks to help indicate the relative position of each valve on a BBC. Print it out and use it if ya like it. , Apr 29, 2023 · Big block Chevy, valve adjustment, roller rocker adjustment, adjusting valves with engine running. Fast accurate valve adjustment. , Contents. 4 Easy Steps on How to Adjust 350 Chevy Valves! Valve Adjustment Procedure Step By Step Guide. 1. Removing Valve Covers and Spark Plugs. 2. Turning the Engine. 3. Finalizing the Valve Adjustment Process., Most hydraulic lift camshafts will require zero lash for the proper adjustment. The process will be the same whether you have stamped steel rockers or roller tip rockers. To achieve zero lash, tighten down the rocker as you spin the pushrod in your fingers, do this until you notice slight resistance as you spin the pushrod (this is zero lash)., The raw performance of these big-blockCorvettes made a dramatic impact in the automotive world, and the 427Corvette legend was born. Choices in 427 big-blocks were expanded in 1967, with three ..., The Family Tree. Unlike lesser engines, the evolution of the big-block Chevy can be traced back to a prestigious great-great-grand pappy, the high-performance 425-hp L78 396, first available in 1965 Corvettes and Chevelles. Even though the big-block was destined to eventually find a home in trucks and family sedans, it started off as a serious ..., Talking Big Brake Upgrades With Wilwood Brakes Technical Info [ January 30, 2024 ] Tips and Techniques For Metal Fabrication You Can Be Proud Of! How To & DIY [ January 30, 2024 ] Crafting A Chevy Trucks Cowboy Boot Shift Knob Builds and Examples [ January 29, 2024 ] High Performance 1962 Pontiac Catalina 4 Speed Revival Builds and Examples , Now for my advertising: I make a special valve cover for adjusting SBC (small block Chevy) hydraulic lifters I call the “Adjust-A-Cover”. EVERYONE that has bought one will tell you that it is the cat’s nuts way to adjust SBC hydraulic lifters. I stock the tall version of an Adjust-A-Cover and it costs $35 plus shipping., Start with cylinder number one (1). When the exhaust valve begins to move, adjust the intake valve to zero lash plus an additional ½ turn more. Rotate the engine over again until the intake valve reaches maximum lift and is almost all the way back down. Then set the exhaust valve to zero lash plus ½ turn. Adjust the valves on each cylinder in ..., May 9, 2019 · Quick fool proof way to set the valves on your Small Block (and Big Block too) for initial start up.UTG T-Shirts Here: https://uncletonysgarage.com/product/u... , Valves. The original Chevy 265-ci small-block began life actuating diminutive 1.72- and 1.50-inch intake and exhaust valves. In the evolution of the small-block, now displacing as much as 454 inches out of a standard deck height block, these big-bore small-blocks can now accommodate up to impressive 2.150- and 1.625-inch valve sizes., Slowly tighten the rocker nut down just until the louder "clatter" stops. Turn the wrench an additional 1/8 - 1/2 turn to set the plunger depth (lifter preload). Continue (repeat) this procedure on each of the remaining the valves. Turn off the engine. Remove your oil splash apparatus and re-install the valve cover., Adjusting valves v8 boat precautions operatingA guide to vortec vs oe small block chevy heads Valve lash adjust engine adjustingChevy block small valves adjust. Chevy block big heads lash valves adjusted set straightSmall block chevy valve lash adjustment with the no. 1 cylinder at top dead center, you can Small block 350 valve …, Start with cylinder number one (1). When the exhaust valve begins to move, adjust the intake valve to zero lash plus an additional ½ turn more. Rotate the engine over again until the intake valve reaches maximum lift and is almost all the way back down. Then set the exhaust valve to zero lash plus ½ turn. Adjust the valves on each cylinder in ..., This instructional video describes two different methods of adjusting valves on engines with solid lift camshafts. The video also briefly talks about firing ... , Chevy Big-Block Performance: Valvetrain Optimization Includes in-depth instruction and photos. Also covers how to disassemble and rebuild any manual transmission. More info on performance mods, clutches and shifters., Number six (6) will be in TDC position. This situation is the classic 180 degrees out of time distributor issue that you may hear about. (4) Adjust both valves at number one (1) to the Specified preload or valve lash if a mechanical lifter motor. (5) Now check all the pushrods on each side of the motor and observe which are up (valve open) …, Steve Morris Engines’ Twin-Supercharged 454 Big Block Chevy Engine. It had been 26 years since the last time Val Morris, Steve Morris’ wife, was behind the wheel of a drag car. The shop had been working on this project car named Sugar Momma, and got it done in time for Sick Week 2024. When it came time to figure out who’d drive it, Steve, If you know all the ins and outs, then only this chart will help you identify everything you need to know. So here it is! Casting Number. Year. Cubic-inch displacement. HP/RPO/Remark. 340220. 1972-76. 427., Also, the stud girdle needs to be on when doing the adjustment. Just loosen the bolt, or bolts, that tighten the jam nut, loosen the set screw in the jam nut, and set the clearance with the feeler gauge. Snug the jam nut and check again. You'll find that sometimes when you tighten the set screw or the bolts on the stud girdle, that the lash ..., When the exhaust valve just begins to open on the first cylinder in the firing order, adjust the intake valve by loosening the adjusting nut slightly while spinning the pushrod until you feel lash in the rocker arm. Tighten the adjusting nut until the slack is taken out of the rocker arm and pushrod., Now for my advertising: I make a special valve cover for adjusting SBC (small block Chevy) hydraulic lifters I call the “Adjust-A-Cover”. EVERYONE that has bought one will tell you that it is the cat’s nuts way to adjust SBC hydraulic lifters. I stock the tall version of an Adjust-A-Cover and it costs $35 plus shipping., With a 2.130-inch intake valve on this big-block, divide this diameter in half to establish the radius, which would be 1.065 inch. Apply a small amount of machinist dye to the valve pocket and ..., The original Chevy 265-ci small-block began life actuating diminutive 1.72- and 1.50-inch intake and exhaust valves. In the evolution of the small-block, now displacing as much as 454 inches out of a standard deck height block, these big-bore small-blocks can now accommodate up to impressive 2.150- and 1.625-inch valve sizes. Much of this ...